--- title: "Connect and Configure Ubiquiti Access Point" slug: "connect-and-configure-ubiquiti-access-point" updated: 2026-04-29T02:08:06Z published: 2026-04-29T02:08:06Z canonical: "support.kiosoft.com/connect-and-configure-ubiquiti-access-point" --- > ## Documentation Index > Fetch the complete documentation index at: https://support.kiosoft.com/llms.txt > Use this file to discover all available pages before exploring further. # Connect and Configure Ubiquiti Access Point Please follow the steps below to connect and configure the Ubiquiti Access Point. ## 1. Physical Connection and Power - **Connect to Network:** Plug one end of an Ethernet cable into the Main/LAN port on the back of the AP. - **Power the Device:** * **If using a PoE Switch:** Plug the other end directly into a PoE-enabled port on your switch. - **If using a PoE Injector:** Plug the AP into the **PoE** port of the injector and connect the **LAN** port of the injector to your router or non-PoE switch. - **Check the LED:** Wait about 60 seconds. The AP's LED ring should eventually turn **steady white**. This indicates it is in a factory-default state and ready for adoption. ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/connect-and-configure-ubiquiti-access-point-image-op6ymdlm.png?sv=2026-02-06&spr=https&st=2026-11-18T20%3A32%3A10Z&se=2026-11-18T21%3A32%3A10Z&sr=b&sp=r&sig=KX%2BfwU21F05uja5%2FNgKFWcLA3JcD%2FmBe68a5MXxLhmQ%3D) ## 2. Access the UniFi Portal You can adopt the device using either the web interface or the mobile app. ### Option A: Using the Web Portal (Best for Detailed Config) 1. Go to [unifi.ui.com](https://www.google.com/search?q=https://unifi.ui.com) and log in with your Ubiquiti account. 2. Select your **UniFi Console** (e.g., Dream Machine, Cloud Key, or self-hosted Network Application). 3. Click on the **Devices** icon (the circle-and-square icon) on the left sidebar. 4. You should see your new AP listed with a status of **Click to Adopt** or **Pending Adoption**. ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/connect-and-configure-ubiquiti-access-point-image-8njs4hwf.png?sv=2026-02-06&spr=https&st=2026-11-18T20%3A32%3A10Z&se=2026-11-18T21%3A32%3A10Z&sr=b&sp=r&sig=4gwzC6rYdvKxKbZgp6N9k0kou6kK5oyE4Qg2PGY%2FSbo%3D) ### Option B: Using the UniFi Network Mobile App 1. Ensure your phone's **Bluetooth** is on and you are connected to the same local network. 2. Open the **UniFi Network app**. 3. The app should automatically detect a "New Device Found." Tap **Adopt**. ## 3. Adoption and Configuration Once you click **Adopt**, the following happens: - **Status Change:** The status will cycle through *Adopting*, *Provisioning*, and finally *Online*. ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/connect-and-configure-ubiquiti-access-point-image-wpxcei6e.png?sv=2026-02-06&spr=https&st=2026-11-18T20%3A32%3A10Z&se=2026-11-18T21%3A32%3A10Z&sr=b&sp=r&sig=OkkNY1DIBVdMlt%2Fn4CgK70jj7dkMqZpNKwg4riam4zQ%3D) - **LED Change:** The LED ring on the AP will turn **solid blue**, signaling it is now managed by your controller. ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/connect-and-configure-ubiquiti-access-point-image-8cp1tj1p.png?sv=2026-02-06&spr=https&st=2026-11-18T20%3A32%3A10Z&se=2026-11-18T21%3A32%3A10Z&sr=b&sp=r&sig=Rw8ddoRHRMnooIu9g%2FI7HjRP2QnpCR%2FHZVTZ3%2F59uNg%3D) To Configure: **![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/connect-and-configure-ubiquiti-access-point-image-emtu5v3b.png?sv=2026-02-06&spr=https&st=2026-11-18T20%3A32%3A10Z&se=2026-11-18T21%3A32%3A10Z&sr=b&sp=r&sig=eEk3LOA0duHWQ9dySjtpoXkWHSNUG4hae6FNVs2Gr6Q%3D)** - **Name the Device:** Click on the AP in the device list. In the panel that opens, go to **Settings** and give it a name (e.g., "Living Room AP"). - **Radios:** Under settings, you can adjust the **Channel Width** (e.g., 40MHz or 80MHz for 5GHz) and **Transmit Power**. - **SSID:** If you already have a Wi-Fi network set up in your Global Settings, the AP will automatically start broadcasting it. ## 4. Troubleshooting: "Device Not Found" If the AP doesn't appear in the portal, check these common fixes: - **Factory Reset:** If the LED is blue or blinking, hold the reset button (near the Ethernet port) for 10 seconds until the LED flashes, then wait for it to turn steady white. - **Layer 3 Adoption:** If your controller is "in the cloud" (not on your local network), you may need to SSH into the AP and run the command: set-inform http://[Your-Controller-IP]:8080/inform - **Firewall Ports:** Ensure port **8080 (TCP)** and **10001 (UDP)** are open on your network for discovery. > [!NOTE] > You can also refer to the video [UniFi Access Point Setup Guide](https://www.youtube.com/watch?v=luZYAMe4A2g) to get details on UniFi Cloud Adoption.