--- title: "MFR30PD Wiring" slug: "mfr30pd-wiring-revised-6-30-2022" updated: 2025-09-11T18:31:13Z published: 2025-09-11T18:31:13Z canonical: "support.kiosoft.com/mfr30pd-wiring-revised-6-30-2022" --- > ## Documentation Index > Fetch the complete documentation index at: https://support.kiosoft.com/llms.txt > Use this file to discover all available pages before exploring further. # MFR30PD Wiring **This document reviews MFR30’s board programming, wiring, and CCM Profile configuration** ## **1) MRF30 Board Programming:** Note: MRF30 Machine must be set to coin and debit mode (This ensures cycle status, otherwise reader will not sense cycle stopped) Programming the machine: Turn the Service key to switch from **RUN** mode to **SERVICE** In Service – SET-UP mode, the Main Menu Screen appears > “**Pricing Menu”** (2nd option listed) > “**General”** (Set-up of Pricing related functions) > Change payment selection to “**Coin & Card”** (2nd option listed) ## **2) MRF30 Harness Wiring:** Machine: MFR30PD PK: Pending Assignment of PK Number ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-84f7t6mt.jpg?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=RNBKMri0h%2FOsAGGcSVXSwGk1GXbIZrzELtgZoJ8Capw%3D) **Coin Connections - Remove machine’s original clear tab connections according to the following directions** ### ***Coin Out to Machine*** Machine green to harness green cable Machine blue to harness blue cable Machine red to harness red cable ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-osvsmtrx.jpg?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=p%2Fa9SZfifYdv5r7XW79JbVXTKBW%2FyHdMj%2B2YZ3%2Bma3s%3D) ### ***Coin In to Terminal*** Machine terminal red to harness green cable Machine terminal blue to harness black cable *Third connection on terminal – Machine's green cable with clear tab remains on terminal* Machine terminal yellow to harness white cable ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-ig0fod65.jpg?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=XrOSC%2BEtg7clnb%2FRiZe6xq1VzfOnqDHzLrRS76moA1E%3D) Coin one – and two ### ***Power Supply Connection:*** The AC Power Adaptor (PS100007) with Brown & Blue pin connector is connected to WH120006 (Black & White Cable) ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-c1iztjd9.jpg?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=PurluV63n7u2ScpmsDBafr4QEf6MIL6T92%2FpuLM5kwY%3D) WH120006 cable uses the blue splice tabs to tap into power on machine. Located on the top left side of the machine (shown in a red circle; see image below) Splice WH120006’ s black cable to machines' black cable Splice WH120006’ s white black cable to machines' white cable Serial connection (orange and black cable) from harness to Machine’s motherboard ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-875qc4ve.jpg?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=K5CRjIcs2ApZe66JCIkoPZtAuGVKViV0zSL3Hkcxsco%3D) Harness’s card reader connection to mesh cable on back of reader The jumper on the *back of the card reader* needs to be changed from “**A**” to “**B**” side ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-f1iizq47.jpg?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=NtPrITK6bk0GNRfr%2FHhaoxBLKVv8P1yWK8lU2faaRy0%3D) ## **3) MRF30 Profile:** Reminder: When using Universal Pulse Profile in CCM Readers must be 2.71.0 or higher & under KLM app reader needs to be programmed as a “CleanReader” not “Ultra” Creating the profile for MFR30 PD under CCM profile builder using the following settings: ![](https://cdn.document360.io/43d8b414-8496-484c-a971-494dc8473827/Images/Documentation/mfr30pd-wiring-revised-6-30-2022-image-3jisdoky.png?sv=2026-02-06&spr=https&st=2026-11-18T20%3A38%3A11Z&se=2026-11-18T21%3A38%3A11Z&sr=b&sp=r&sig=F77cBhKlEJFIXo%2FxoWMvGxO45fVd0gYsWMNxWIFS5%2B4%3D) CCM Profile > Universal > Universal Pulse > Pulse Output: **RelayPulse** Output Pulse Gap: **100** Pulse Polarity: **Idle Open** Output Pulse Duration: **50** Laundry Available Signal: **Low**