Tap the KioSoft logo on the top center of the Ultra VXT for five times and input the 8–digit password to enter the main menu.

图片 1, 图片 The table below is the main menu list.

Menu Item	Options	Description
Terminal Config	/	Access to the Terminal Config Menu
Inject Key	Dep Key Key Card	Access to the Inject Key Menu
Reset Card Counter	/	Access to the Reset Card Counter
Site Code Config	/	Access to the Site Code Config function
Collect Cash	/	Access to the Collect Cash function
Audit Cash	/	Access to the Audit Cash function
Work Mode	/	Access to the Work Mode Menu

1. Terminal Config

The Terminal Config Menu is entered by tapping the admin card and inputting 4–digit admin password. There are twelve sections of this menu with functions displayed as follows:

Demo mode

图片 4, 图片

The demo mode is mainly used for simulation and demonstration in terms of topping up and making transactions. Once the demo mode is turned on, transaction tests could be done on the Ultra VXT. You could select “YES” to turn on Demo mode as shown in the picture.

Config > Edit Setup

This function is used to set and edit all parameters for the kiosk.

Tap “EDIT” to edit parameters and tap “OK” to confirm and continue to check other parameters. When you finish editing all necessary parameters, you could tap “CANCEL” to exit the function. Once you exit, select “YES” or “NO” to save or quit editing.

Below table is the instruction for all parameters in Config.

Parameter Name	Description	Remark
Print Receipt	This function is not applicable for VC kiosks.	N/A
Force Confirm	This function is not applicable for VC kiosks.	N/A
Printer Setup Internal	This function is not applicable for VC kiosks.	N/A
Print Screen	This function is not applicable for VC kiosks.	N/A
Card Dispenser	This defines if the card dispenser peripheral is enabled or not.	/
Value Code	This defines if the Code Based Revalue is enabled or not.	/
Cash Validator	This defines if support external cash/bill validator.	/
Blankcard Price	This defines the card price for cards dispensed by card dispenser.	/
Site Code	When set more than 2 site codes into the terminal, if this parameter is set to Enable, while use a blank card to add value, terminal will ask to input site code. If this parameter is set to Disable, while use a blank card to add value, terminal won’t ask for site code, but will write the first site code into the card.	/
Site Code Value	This parameter defines the site code values that the terminal will accept.	/
LOC Code	This is a unique value of the location, also referred to as Location ID or ULN.	/
ULN OR LOC CODE	This parameter is used to select which name will be used as the parameter’s name to show the terminal’s location ID, ULN or LOC CODE.	/
DISP IDLE MSG LINE 1	The first line displayed on the Idle Page. The default content is blank. The content can be defined manually.	For English Version
DISP IDLE MSG LINE 2	The second line displayed on the Idle Page. The default content is blank. The content can be defined manually.	For English Version
DISP IDLE MSG/FR LINE 1	The first line displayed on the Idle Page. The default content is blank. The content can be defined manually.	For English Version
DISP IDLE MSG/FR LINE 2	The second line displayed on the Idle Page. The default content is blank. The content can be defined manually.	For English Version
CARDADDED AMT 1	This parameter is the amount option 1 when add value to the card.	/
CARDADDED AMT 2	This parameter is the amount option 2 when add value to the card.	/
Rpt Upload Time	This parameter defines the time at which the terminal will upload the report to TTI host.	/
Rpt Upload IP	This parameter defines the IP that the terminal will connect to for uploading the settlement report and audit log to TTI host.	/
Rpt Upload Port	This parameter defines the IP port that the terminal will connect to for uploading the settlement report and audit log to TTI host.	/
RPT Transfer SER ID	This parameter defines the report transfer server ID.	/
Cards Counter	This parameter defines the max card's counter in card dispenser or Phelps project.	/
Printer Paper	This function is not applicable for VC kiosks.	N/A
Max Card Amount	Maximum amount in the Mifare Card, default 9999, range is [100, 9999] unit is cents.	/
Max Cash	This parameter sets the maximum cash amount that can be loaded in the cassette. The unit is dollar. If the cash in the cassette reaches this value, it will report to the server then the trans "Add cash to the card" won't be allowed.	/
Cash Threshold	The unit is dollar. If the cash in the cassette reaches this value, it will report to the server.	/
SUPT Bill Type	It set the denominations accepted by the device. The unit is dollar. A comma "," is a delimiter. E.g., if set to "1,2,5,10", it means 1 dollar, 2dollar, 5dollar, 10dollar can be accepted by the device.	/
Cash Timeout	This defines the terminal can put cash timeout value while use cash to pay fee, default is 180s, unit is second.	/
CUST Service #	This parameter sets the displayed below "add to card failed" in the screen when add to card failed by Cash.	/
Cash Full Msg1	This defines line 1 in English of the display message while the cash acceptor counter gets the MAX CASH.	/
Cash Full Msg2	This defines line 2 in English of the display message while the cash acceptor counter gets the MAX CASH.	/
Cash Full Msg3	This defines line 3 in English of the display message while the cash acceptor counter gets the MAX CASH.	/
Low Card Level	This parameter defines that warning message should be displayed while left card in card dispenser is equal or less than this value.	/
Low Printer Level	This function is not applicable for AVU kiosks.	N/A
LogServer Debug	It is used in PTIP open solutions and decide debug information should be sent to where: logserver or serial port.0=serial port, 1=logserver.	/
Log Server IP	This parameter defines logserver IP.	/
Log Server port	This parameter defines logserver port.	/
Display Timeout	This parameter defines screen display timeout (unit: sec).	/
Screen Timeout	This parameter defines the screen timeout for the laundry main app. Default is 10 sec and the max value is 99 sec.	/
Tap Timeout	This parameter is used in Phelps project, which defines the timeout value while prompt tap card. 0 means no timeout, value is 0-00.	/
Language	This parameter defines terminal language.0-English, 1-French 2-S Chinese 3-T Chinese.	/
Laundry TID	Unique terminal identifier.	/
Card Tap Text	Define to control LCD display text on PTS to guide customer to hold card on card reader, 0=Place card in Card Slot, 1= HOLD CARD ON READER.	/
DB SurCharge	The value of Debit surcharge (Canada).	/
CONVEN Fee	The value of Credit surcharge (Canada).	/
Batch Record	The maximum quantity of batch saved.	/
EVERLINK TID	A Unique ID provided by EVERLINK that associates the POS device with a unique merchant hierarchy.	For Canada market
Admin password	To protect any item in admin menu. e.g., enter Terminal config. site code config. collect cash.	/
Key Value	The value of the key after key injection on KLM.	/
LED Indicator	This function is not applicable for AVU kiosks.	/
NMS Server IP	This parameter defines NMS Server IP address.	/
NMS Port	This parameter defines NMS port.	/
NMS Login Name	This parameter defines NMS username.	/
NMS Login PWD	The login password for NMS.	/
NMS Period	This parameter defines NMS auto update period.	/
NMS Enable	This parameter defines whether to enable/disable NMS function.	/
PRI Host IP	The prioritized IP option of TSYS Host.	/
PRI Host Port	The prioritized port option of TSYS Host.	/
SEC Host IP	The backup IP option of TSYS Host.	/
SEC Host Port	The backup port option of TSYS Host.	/
DHCP Enable	This parameter defines whether to enable/disable DHCP function.	/
IP Address	The IP address in use of the kiosk.	/
Gateway	The Gateway of the kiosk.	/
Subnet Mask	The Subnet Mask of the kiosk.	/
DNS	The server address of DNS.	/
POS ID	One of the parameters of TSYS account.	/
AUTH Code	One of the parameters of TSYS account.	/
MERCH Zip Code	One of the parameters of TSYS account.	/
MERCH Cat Code	One of the parameters of TSYS account.	/
Routing ID	One of the parameters of TSYS account.	/
MTREX Username	To reboot MTREX modem via PTS terminal	/
MTREX Password	To reboot MTREX modem via PTS terminal	/
MTREX IP	The IP to visit the MTREX modem.	/
MTREX Port	To reboot MTREX modem via PTS terminal	/
Cents Top Up	The field is used to decide whether users could use cents to reload wallet balance. If it is enabled, cents are supported. If it is disabled, only dollars can be used.	/
Display CVC	Laundry app if display the CVC code when tap value card.	/
Alive Msg Time	This parameter defines time when terminal will upload a live report. Time to be entered in format HHMMSS (HH: 00-23; MM: 00-59; SS: 00-59).	/
Reboot Time	This parameter defines time when terminal will reboot during the day. Time to be entered in format HHMM (HH: 00-23; MM: 00-59).	/
Fallback Enable	Enable/disable whole fallback function to stop swiping card after insert a damaged IC card.	/
Suggest Amount 1	The recommended refill amount displayed in the first place: The default value is $ 5.00.	/
Suggest Amount 2	The recommended refill amount displayed in the second place: The default value is $ 10.00.	/
Suggest Amount 3	The recommended refill amount displayed in the third place: The default value is $ 15.00.	/
Suggest Amount 4	The recommended refill amount displayed in the fourth place: The default value is $ 20.00.	/
Suggest Amount 5	The recommended refill amount displayed in the fifth place: The default value is $ 25.00.	/
Suggest Amount 6	The recommended refill amount displayed in the sixth place: The default value is $ 30.00.	/
Help MSG Line 1	The first line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For English version
Help MSG Line 2	The second line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For English version
Help MSG Line 3	The third line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For English version
Help MSG Line 4	The fourth line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For English version
Help MSG Line 1 SP	The first line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For Spanish version
Help MSG Line 2 SP	The second line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For Spanish version
Help MSG Line 3 SP	The third line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For Spanish version
Help MSG Line 4 SP	The fourth line displayed after clicking the “?” at the upper-right corner on the Idle Page: The default content is blank. The content can be defined manually.	For Spanish version
IDLE MSG LINE 1	The first line displayed on Idle Page: The default content is “LEASE TAP YOUR”	For English version
IDLE MSG LINE 2	The second line displayed on Idle Page: The default content is “CARD HERE”.	For English version
IDLE MSG LINE 1 ESP	The first line displayed on Idle Page; The default content is “ACERQUE”.	For Spanish version
IDLE MSG LINE 2 ESP	The second line displayed on Idle Page; The default content is “SU TARJETA”.	For Spanish version
Network Connectivity	The parameter defines the network connectivity for Cash Only mode. Default setting is Disabled.	For Cash Only mode

General

About

图片 28, 图片

Select “ABOUT” and some general information will be displayed on the screen, such as the APP name, APP version and the APP build date.

Note: The keypad will be changed later. For now, as shown in the pic, “X” stands for cancel, “<” for delete, “O” stands for OK, “U” for Page Up, “A” for editing and “D” for Page Down.

Parameter Download

图片 25, 图片

The parameters such as Card Price, Credit Card Processing information, etc. need to be downloaded so that the Ultra VXT can operate normally.

Input the reference number provided by KioSoft and tap “O” (representing OK) to start parameter downloading.

The default server IP address and port will be auto filled, please check, and tap “O” (representing OK) to confirm. When the “Download Succeed” message is displayed, it means your parameters are downloaded and configured successfully.

图片 22, 图片

图片 16, 图片

图片 19, 图片

Buy/Add Config

图片 2033752893, 图片

Three parameters relating to Cash One mode can be configured herein as follows.

Multiple Cards defines whether to allow the purchase of multiple cards in one transaction.
Max Cards Qty defines the maximum number of cards that can be purchased in one transaction.
Combine Buy/Add determines whether to allow the combination of buying card and adding value in one step so users don’t need to pay for buying a card in the first step, get the card and make payment again to add value in the second step.

Note: these paramters will be displayed only when Cash One mode is selected as the Work Mode.

Multiple Cards: Tap “YES” to enable it or “Back” to return to Buy/Add Config page.

It is disabled by default.

Max Cards Qty: Tap the keyboard to enter the max quantity and “Confirm” to save the settings.

Default value is 5 and range is 2-10.

Combine Buy/Add: Tap “YES” to enable the function so users can add value to the new card directly before the card is dispensed.

It is disabled by default.

图片 2033752896, 图片

图片 2033752895, 图片

图片 2033752898, 图片

Activate POS

Tap “Activate POS”, and below images will be displayed on the Ultra VXT, when you see the last “Activated” image, it means you activated the POS successfully.

图片 31, 图片

图片 34, 图片

图片 37, 图片

NMS Download

Tap “NMS Download” and it will automatically download and update parameters.

Firmware Upgrade

Tap “Firmware Upgrade” and it will automatically get upgraded.

Kiosk Mode

This parameter is only applicable to amusement installations. Either value mode or credits mode could be selected in this function.

Settlement

图片 2033752852, 图片

This function is used to do settlement for all transactions. After settlement, the record will be uploaded to Washboard and will be cleared in the Ultra VXT.

Settlement is finished after you see below image. Tap “O” (representing OK) in the red box to exit this function.

Test Dispenser

Tap “Test Dispenser” and the dispenser will automatically get tested. If the dispenser works, a card will be dispensed.

IP Mode

图片 43, 图片

Standard mode: The Ultra VXT will call to your NMS every 4 hours

Data Save: The Ultra VXT will only perform NMS update daily at rebooting time.

Reboot MTREX

The Ultra VXT will reboot the router once receiving the reboot the cellular modem command. This will only function if using a KioSoft-provided router.

Reset LT

图片 46, 图片

Reset lifetime, this function is used for Cash Kiosk to clear the lifetime of the cashbox.

2. Inject Key

Register Key

To register the key, you need to tap the Deployment Key Card and Key Card, and input the vendor ID.

Note: This function is for KioSoft Technicians use only.

You can also inject vendor key for the Kiosk via KLM.

Minimum Version Supported: VXT Kiosks 1.13.7 KLM 3.0.0

1) Click “Inject Key” in the admin menu on the Kiosk screen.	2) Select “Key Injection with KLM” on the screen.	3) The Kiosk will display its QR code and machine number.

4) Click “Inject Vendor Key” on the interface of “Install”. Then there are two approaches to injecting the vendor key, either scanning QR Code or Entering machine number.	5) Select “Kiosk” to inject vendor key.	6) You can select to enter machine number or scan QR code to help KLM find the device.

7）The Kiosk screen will display the key injection process as shown below.	8）After the key injection is finished, a prompt message will pop up to remind you of the result of the key injection.

Clear Key

To clear the existing key, you need to tap “CLEAR”.

3. Reset Card Counter

Tap “Reset Card Counter”, tap the admin card, and input the 4 – digit password, the screen will display “Reset Game Card”, tap it and then tap “Confirm”.

4. Site Code Config

This function is mainly used for changing the site code of site cards or single cards.

Note: This function is used for setting up cards for card readers for legacy products that do not support Bluetooth.

5. Collect Cash

图片 28, 图片

Tap “Collect Cash”, tap the admin card and input the 4–digit password, then tap the Cash card and the screen will display as shown in below picture.

You can also perform cash collection via KLM.

Note: This function only works on Kiocentral server. 

1) Press on the sandwich menu button and click “Cash Collection” in the list. 

2) Click the button bordered in blue to proceed Collection with your location, before which make sure Internet Connection is available and you have confirmed the Location. 

3) The rooms of your Location will be displayed on the new page. Select the room in which you want to complete cash collection. 

*There will be an icon on the right of the room if all the money for all the machines in it has been collected. 

图片 31, 图片

图片 30, 图片

图片 29, 图片

Bag Collection 

If “Bag Collection” is enabled in “KLM -> Settings”, the options are “Bag Collection” “Scan Machine QR Code” and “Enter Machine Number”. 

4) Click “Bag Collection” and scan the bar code on the collection bag. Then scan QR Code or enter Machine Number to decide the machine whose cash is to be collected. During the process, the number of machines collected will be updated.	5) Successful collection is displayed on the screen. And related info like the number of coins and bills can be checked. After you finish the cash collection for a single machine, the data will be uploaded to server automatically in the background.

6) Click the “Show Details” button on the complete collection page and it will direct you to the machine list page. You can see from the picture below that the amount of cash and credit for this collection will be displayed under each machine.	7) After one cash collection, if you exit the room list and confirm location again to enter the machine list page, you will see as below picture displays that all machines’ status turns to be “Not Collected”. Besides, the data of last collection including the amount of cash and credit as well as the collection time will be imported from server and displayed on the app.

Set Loyalty Card