Document Overview

The objective of this document is to cover how to setup a Alliance Quantum Pro controlled machine using coin. This document goes over the wiring of a Quantum Pro with connection kit PK120058.

Additionally, how to create a the machine’s profile in the Cloud Configuration Manager, used for

programming the KioSoft card reader.

Parts List

Harness Connections Illustration

WH120011 ACA harness with Coin Drop Connector

Reader Firmware Requirement

The Quantum Pro machine profile is supported on Solo connects starting at version 1.24.3 and up. Non- connected readers must be on version 2.24.3 or higher.

You may receive a red “X” after attempting to program the reader on KLM app if the version below requires Quantum Pro. To update firmware on the reader, you will need a modem on site and update via KLM app or use a download station.

Machine Board Firmware Requirement

We recommend version 5.000, 7.000, and 8.000 for all readers. Firmware can be checked by turning the laundry machine on and off. The firmware version will flash quickly on the display.

If the version is not 5.000, 7.000, or 8.000 you will need to upgrade or downgrade the firmware version on the machine. Please contact Alliance if you need assistance with board firmware.

Programming machine board into CARD Mode

In order for the card reader to work with an Alliance Quantum Pro controlled machine , the board must be set to CARD mode.

The following is a quick walk through on how to change the programming on the board. Please see the

owner’s manual for your specific laundry machine. See table below for navigating the menu

1. Enter service mode by unplugging the bullet plug that is connected to the board. Located

between the “white/black” and “red/blue” wires.

1. Once the bullet plug is removed, hold the service switch in the back of the coin vault and press the top left and middle left buttons. The machine should show “rAPid” on the display.

2. Press the UP button to select Prog. Once here scroll through the menu options until you see

SErPAy. Press START once you reach SErPay.

• 1. For washers, you scroll through until option 15

  2. For dryers, you scroll through until 8

1. By default, this setting will be set to “SEriAL” on the machine board, press the up button to set this to “CArD”. Once on CArD, press START to save.

2. The next setting will be “CArDEn”, press START again to edit. By default, this will be set to off, press the UP button to set this to ON and press START button to save.

3. Once these have been changed, press BACK button until you are back to the price.

Before Installation

PLEASE UNPLUG LAUNDRY MACHINE PRIOR TO INSTALLATION OF HARNESS

Wiring Instructions

Serial Connection

Connect WH120011’s card reader serial connection into machine board.

Coin Connection, If appliable

Connect the machine's coin cable into WH120011’s 3-pin male coin cable (red, black & white).

Power Connection

Plug in KioSoft WH120011’s black and white power cable into machine’s 2-pin power connection on board

Reader Connection

Plug card reader’s data cable into harness WH120011’s card reader cable

Creating a profile

Under CCM, in the Profile Builder:

Select the following for Machine Data

Select Manufacturer as “Alliance”

Select Machine Control Type as “Quantum Pro”

Select Machine type:

After, click on "Advance Options" and configure machine fields (vend price, time, etc.,) as needed.

Once machine values are configured, click on “Site Data” and enter location information.

• Site Code and Location ID must match the location in Location Management on Laundry Portal

• For Location ID and Room#, you should enter the ones that you created previously

See image below regarding Site Data’s field values.

1. Location ID

2. Site Code

3. Room Number

   • Each room will get its own profile.

4. Non-Network

   • This should be enabled any time a modem is not present in the room.

5. Card Holder

6. Hide Label

   • This will hide the machine number on Connect and Elevate readers

If applicable, for Payment Options, ensure you select the payment methods for the desired location.

Finally, select “Save Profile” from the drop-down menu and click “Save”

• Enter “Custom Text” for easier identification in the KioSoft Laundry Manager Application.

• Example of Custom Text Label: Location Name RM1 MACHINECONTROL Dryer [225/45mins]