Parts List

Part Number

Part Name

Items Included

PK120068

Reader Installation Kit - Alliance (Quantum/ACA - C,N,X Models)

WH120011 ACA harness with Coin Drop Connector
WH120006 ACA Power Washer Cable
PS100007 Power Adaptor, 12V for CleanReader
WH120015 Connect Cable to ACA power adaptor
PL100002 Surface Universal Back Mounting Plate
x2 - PP000003 Wire Tap Splicer

Parts Illustration

WH120011 ACA harness with Coin Drop Connector

Safety reminder: Please unplug washer machine prior of installation of KioSoft Equipment

Changing machine board to SERIAL mode

With the ACA machine off, verify the machine is set to “Serial Payment System” mode by looking at the dipswitches on machine board.

Dipswitches are located on the bottom left of the board. Only dipswitch 3 needs to be on, all others are off. See example of machine board images below.

If the machine is left on while making changes to the dipswitches, the changes may not take effect. Power cycle the machine afterwards.

***Image: ACA Machine Logic board image***

Image: Logic board zoom in with Dipswitch set on number 3

Wiring Instructions for connector solo readers

Remove front panel screws of the machine to reveal ACA motherboard. Example of machine board shown below.

Image: Machine board open view

Serial Connection

Connect the WH120011’s card reader serial cable to the machine board, located on the top left-hand side.

Image: WH120011’s serial cable connected to machine board

Power Connection

There are two methods for getting power from machine, depending on the type of reader.

For Connect & Solo Readers, use the “H10” on the ACA motherboard and WH120020, included in harness kit. H10 connection on the board is located above the dipswitches.

Image: connection to ACA motherboard

Connect KioSoft harness female power cable (black & white) to male connection on WH120020.
Then connect the female end of the WH120020 cable to the “H1” connection on the board.

Image: WH120020 wire connection to Motherboard

Wiring instructions for Ultra reader settings

For Ultra reader, reader will receive power using the transformer with additional parts: AC/Adaptor PS100007 with WH120021, and WH120015.

Image: WH120021 Wire

Image: WH120015 wire

Image: PS100007 AC power adaptor

Disconnect the machine’s transformer connection
Image: wiring description for step a
Connect machine’s male transformer connection to WH120021’s female power connection.
Then WH120021’s male power connection to machine’s female transformer connection.
Image: Wiring description for step b.
Connect the third cable (male connector) from WH120021 to the AC/Adaptor’s female connector (brown & blue) and the other end of the AC adaptor cable (male connector, red and black) to WH120015 female connector.
Finally, connect WH120015 into WH120011 harness’s cable (black and white).

***Image: wiring description for step d.***

Coin connection, if appliable

Connect the machine's coin cable into WH120011’s 3-pin male coin cable (red, black & white).

***Image: wiring connection for coin cable***

Reader connection

Plug card reader’s data cable into harness WH120011’s card reader cable

***Image: Wiring connection for card reader***

Creating an ACA profile

Under CCM, in the Profile Builder:

Select the following for Machine Data

Select manufacturer as “Aliance”

Select Machine Control Type as “ACA”, then, select machine type:

Please note: The ACA laundry machines from year 2020 need an ACA MAX profile.

With an ACA MAX profile, the reader is pulling the vend price from the machine board. You must set the desired vend price on the machine board.

After, click on "Advance Options" and configure machine fields (vend price, time, etc.,) as needed.

Once machine values are configured, click on “Site Data” and enter location information.

Site Code and Location ID must match the location in Location Management on Laundry Portal
For Location ID and Room#, you should enter the ones that you created previously

See image below regarding Site Data’s field values.

Location ID
Site Code
Room Number

- - Each room will get its own profile.

Non-Network

- - This should be enabled any time a modem is not present in the room.

Card Holder
Hide Label

- - This will hide the machine number on Connect and Prime readers

If applicable, for Payment Options, ensure you select the payment methods for the desired location.

Finally, select “Save Profile” from the drop-down menu and click “Save”

Enter “Custom Text” for easier identification in the KioSoft Laundry Manager Application.
Example of Custom Text Label: Location Name RM1 ACA Dryer [225/45mins]

Insert the ACA Cable With Coin into the Elevate Express

Connect P4 to Coin Drop, connect P2 to one end of H10 Power Cable, and connect P3 and the other end of the H10 Power Cable to the Machine Board.

Deploy 1. Install