Document Overview

The objective of this document is to cover how to connect a KioSoft card reader to a Fagor laundry machine. This document goes over the wiring of a Fagor machine with connection kit PK1F0001.

Additionally, how to create a the machine’s profile in the Cloud Configuration Manager, used for programming the KioSoft card reader.

Parts List

Harness Illustration

WH1F0001 Fagor Washer Cable With Coin

WH111004 120Vac Long Power Cable, Universal

Before Installation

PLEASE UNPLUG LAUNDRY MACHINE PRIOR TO INSTALLATION OF HARNESS

Wiring Instructions

Coil Relay Connections

Connect WH1F0001’s female spades to the 220 VAC coil relay included in the kit, with the orange cable spade to the top left and the green colored cable underneath. See reference photos below.

Then connect WH110053 female spades to the coil relay’s “NO” and “COM”. The “NC” on the 220 VAC

coil relay is not used.

Located the CN8 connection on the machine board and use the T-Splices on the red and blue cable.

The connect the WH110053’s spades into the t-splices, as shown below

Power Connection

Please consult the Owner’s Manual, under the installation section, before fully connecting WH111004 & PS100007 Power Adaptor to your laundry machine. Depending on the machine model and voltage, connections may vary. PS100007 Power Adaptor accepts a wide input from 100-240 V – 50-60HZ 0.8A and output of 12V.

WH111004 is fed from the front of the machine through the back, to reach power connections. For this example, WH111004’s white cable is tapped into Neutral and black cable to L1.

Then plug in AC adapter PS100007’s 2-pin female connector to the WH1F0001’s power cable, black and

white.

Connect WH111004 to the PS100007’s 2-pin connector

Coin Connections

Connect harness WH1F0001’s 3-pin coin pulse cable into the back of the card reader.

Plug in WH1F0001’s male 6-pin coin connector into the machine’s 6-pin female connector.

Plug in WH1F0001’s female 6-pin coin drop connector into the machine’s coin drop connector.

Card Reader Connection

Plug card reader’s data cable into WH1F0001’s card reader connection.

Please note: Card reader jumper remains on “A” side with the CommonPulse Profile.

Creating a CommonPulse profile

Under CCM, in the Profile Builder:

Select the following for Machine Data/mdata:

Manufacturer: “CommonPulse”

Machine Control Type: “Washer”

After, click on "Advance Options" to view all fields:

Configure machine parameters/fields as needed:

Note: All parameters in the machine’s profile will need to match what is set on the

machine board.

The Cycle Time is the amount of time the reader will not accept payment once the machine is in use. Please make sure to change the cycle time as needed.

Enter the following pulse setting for a Fagor Washer

Pulse Output = Coin Pulse

Pulse Width = 65 Pulse Rate = 300 Pulse Type = Low

Laundry Available Signal = High

Once machine values are configured, click on “Site Data” and enter location information.

• Site Code and Location ID must match the location in Location Management on Laundry Portal

• For Location ID and Room#, you should enter the ones that you created previously

See image below regarding Site Data’s field values.

1. Location ID

2. Site Code

3. Room Number

   • Each room will get its own profile.

4. Non-Network

   • This should be enabled any time a modem is not present in the room.

5. Card Holder

6. Hide Label

   • This will hide the machine number on Connect and Elevate readers

If applicable, for Payment Options, ensure you select the payment methods for the desired location.

Finally, select “Save Profile” from the drop-down menu and click “Save”

• Enter “Custom Text” for easier identification in the KioSoft Laundry Manager Application.

• Example of Custom Text Label: Location Name RM1 Fagor Washer [3.50/45mins]

Additional Information